TSL1401CL【PDF 3/17 页】IC LINEAR SENSOR ARRAY 128X1 CL

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录57

1页 2页 [3页]4页 5页 6页 7页

TSL1401CL

128 ?1 LINEAR SENSOR ARRAY WITH HOLD

TAOS136 JULY 2011

The LUMENOLOGY r Company

www.taosinc.com

Terminal Functions

TERMINAL

NAME

NO.

DESCRIPTION

Analog output.

CLK

Clock. The clock controls charge transfer, pixel output, and reset.

GND

6, 7

Ground (substrate). All voltages are referenced to the substrate.

5, 8

No internal connection.

Serial input. SI defines the start of the data-out sequence.

Supply voltage. Supply voltage for both analog and digital circuits.

Detailed Description

The sensor consists of 128 photodiodes arranged in a linear array. Light energy impinging on a photodiode

generates photocurrent, which is integrated by the active integration circuitry associated with that pixel.

During the integration period, a sampling capacitor connects to the output of the integrator through an analog

switch. The amount of charge accumulated at each pixel is directly proportional to the light intensity and the

integration time.

The output and reset of the integrators is controlled by a 128-bit shift register and reset logic. An output cycle

is initiated by clocking in a logic 1 on SI. For proper operation, after meeting the minimum hold time condition,

SI must go low before the next rising edge of the clock. An internal signal, called Hold, is generated from the

rising edge of SI and transmitted to analog switches in the pixel circuit. This causes all 128 sampling capacitors

to be disconnected from their respective integrators and starts an integrator reset period. As the SI pulse is

clocked through the shift register, the charge stored on the sampling capacitors is sequentially connected to a

charge-coupled output amplifier that generates a voltage on analog output AO. Simultaneously, during the first

18 clock cycles, all pixel integrators are reset, and the next integration cycle begins on the 19

clock. On the

129

clock rising edge, the SI pulse is clocked out of the shift register and the analog output AO assumes a

high impedance state. Note that this 129

clock pulse is required to terminate the output of the 128

pixel, and

return the internal logic to a known state. If a minimum integration time is desired, the next SI pulse may be

presented after a minimum delay of t

(pixel charge transfer time) after the 129

clock pulse.

AO is an op amp-type output that does not require an external pull-down resistor. This design allows a rail-to-rail

output voltage swing. With V

= 5 V, the output is nominally 0 V for no light input, 2 V for normal white level, and 4.8 V

for saturation light level. When the device is not in the output phase, AO is in a high-impedance state.

The voltage developed at analog output (AO) is given by:

out

= V

drk

+ (R

) (E

)(t

int

)

where:

out

is the analog output voltage for white condition

drk

is the analog output voltage for dark condition

is the device responsivity for a given wavelength of light given in V/(糐/cm

)

is the incident irradiance in 糤/cm

int

is integration time in seconds

A 0.1 糉 bypass capacitor should be connected between V

and ground as close as possible to the device.

The TSL1401CL is intended for use in a wide variety of applications, including: image scanning, mark and code

reading, optical character recognition (OCR) and contact imaging, edge detection and positioning, and optical

linear and rotary encoding.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式